How To Use A Chainsaw Depth Gauge

  • How to Use the Stihl Depth Gauge Tool
  • Position the chainsaw on a sturdy work surface with an adequate source of light.
  • Lay the depth gauge tool along the top of the chain. Check to see if a depth gauge point appears above the level of the depth gauge tool.
  • Make the point level with the surface of the tool using a flat file.
  • More items
  • via

    What does a chainsaw depth gauge do?

    A depth gauge is used to provide a flat surface across the teeth of your chainsaw's teeth to provide a guideline for filing them down to the same height. via

    How do you use a Stihl Raker depth gauge?

    How do you use a Husqvarna chainsaw depth gauge?

  • PLACEMENT Place one of the holes in the gauge over one of the depth gauges on the chain.
  • HOLD THE GAUGE FIRMLY IN ONE HAND Hold the flat file in your other hand and file the depth gauge until the file comes in contact with the gauge.
  • via

    What is chainsaw depth?

    Depth gauges, "riders," or "rakers," as they are sometimes called, control the amount of wood severed by a cutter tooth. As you can see in the graphic, the top of the cutter tooth slopes back. Each time the chain is sharpened, the top corner of the cutter tooth gets lower. via

    How do you grind a depth gauge on a chainsaw?

    How do you grind rakers on a chainsaw?

    How do you sharpen rakers?

    How is Raker depth measured?

    How do you use a depth gauge tool?

    How do I know what size my chainsaw chain is?

    What do the high and low screws do on a chainsaw?

    Most Pro Saw Engines Have Three Carburetor Adjusting Screws:

    If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. Low Speed Fuel Adjustment - This is the adjustment that controls the proportion of fuel in the air/fuel mixture at idle speed. via

    How do I know what angle to sharpen my chainsaw?

    The right sharpening angle depends on the saw chain and the wood that you want to cut. The sharpening angle will generally be between 25° and 35° – the harder the wood, the greater the angle. To maintain the correct angle, we recommend that you use a sharpening grid or a filing gauge as an aid. via

    What are chainsaw rakers?

    The depth gauge (rakers) on a chainsaw control how deep the cutter teeth penetrate. Because the top plate of the cutter tooth is angled back slightly, it is essential that the depth gauge be lowered as the cutter teeth are filed back. via

    When should you replace the bar on a chainsaw?

    If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar. via

    How do you sharpen a chainsaw hand?

    How do you use a chainsaw filing guide?

    Can you sharpen a chainsaw with a flat file?

    A flat file. A depth-gauge guide for resetting the depth gauges. Pro tip: Don't use a standard rattail file as a chainsaw sharpener. Its tapered diameter and coarse teeth will ruin your chain's cutters. via

    How can I make my chainsaw cut faster?

    What angle do you sharpen a Stihl chainsaw?

    STIHL saw chains are generally filed to an angle of 30° – parallel to the service mark for the filing angle. Hold the file so that one quarter of its diameter projects above the top plate. via

    How do you shorten a chainsaw chain?

    What does pitch and gauge mean on a chainsaw chain?

    Pitch: the distance between the chain's drive links. Gauge: the width of the groove where the chain fits into the bar. via

    How does the chain on a chainsaw work?

    Most simply put, a chainsaw works by spinning a chain of saw blades, also called “teeth”, around a guide bar quickly to cut through wood in a fast, smooth motion. Together, the chain and guide bar are referred to as the chain assembly which is powered by the engine/motor. via

    How do you sharpen a chainsaw with a Timberline Chainsaw Sharpener?

    How do I choose a chainsaw file?

  • #Step 1. Identify the pitch, gauge or Item Number.
  • #Step 2. Use the chart below to Identify your file size.
  • #Step 3. Pick how many you would like to order, we offer chainsaw files in packs of 3's and 12's. Chainsaw files size chart. Pitch. Gauge. Item No. File Size. Sharpening Angle.
  • via

    How do you use a chainsaw flat file?

    How do you use a stump vise?

    What is the difference between .325 and 3/8 chain?

    The three-eighths chain is a beefier saw and better suited to one that has more horsepower. It has larger teeth and a heavier duty chain, so it requires more horsepower to operate correctly. 325-inch chain for those saws between 40 and 60 cc. via

    What are chainsaw file sizes?

    The main types of files are the 4mm, 4.8mm, and the 5.5mm files. These files can either flat files or round files depending on the cutter you are sharpening. If you have a chain with a chipper cutter, you will go for a round file. via

    What do numbers on chainsaw chain mean?

    The numbers stamped on a chainsaw chain are an ID code used by the manufacturer to indicate the pitch and gauge measurements of the chain. Pitch and gauge are important dimensions which influence whether or not a chain is compatible with a chainsaw. via

    What does the L and H mean on my chainsaw?

    They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet). via

    Why does my chainsaw bogs down at full throttle?

    If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly. via

    Why does my chainsaw only runs on choke?

    If your chainsaw only runs with the choke on, it is likely an issue with your carburetor. If the carburetor is plugged, the engine will be starved of fuel and will not run. However, if the engine is plugged, the choke will pull more fuel through the carburetor's idle circuit and allow it to run. via

    What is the most aggressive chainsaw chain?

    A . 404″ chainsaw pitch is the most aggressive chainsaw chain pitch for professional arborists. via

    Why does my chainsaw chain dull so quickly?

    If your chain dulls quickly, then it could be a couple of things. Your chain will cut too deep or barely cut at all if your rakers or depth gauges are filed down too much or not enough, respectively. Get yourself a depth gauge appropriate for your saw and use it every time you sharpen your chain. via

    Is it worth sharpening a chainsaw chain?

    As dozens of cutter teeth chew through dense wood, they're bound to become dull, reducing the tool's effectiveness and making it more physically demanding for you to control. Regular sharpening, accomplished by filing, will keep your chainsaw purring like a very rugged kitten. via

    Leave a Comment

    Your email address will not be published. Required fields are marked *